中空玻璃打膠是個技術活，要做到不漏氣才可以，那么中空玻璃要怎樣打膠怎樣才能不漏氣？接下來我們一起聽聽全自動封膠機廠家的說法吧！
Interruption of hollow glass is a technical work, to do not leak can, then how to glue hollow glass how to do not leak? Next, let's listen to the manufacturer of automatic sealing machine.
翻開氣泵開關，電源總開關，控制臺開關，在控制臺按手動按鈕，然后在顯現屏上找到原點設定，點擊輔助原點設定，然后點擊頭部原點設定，留意原點設定時防止頭部和輔助吸盤碰撞。等設定好然后返回找到玻璃厚度設定，先是玻璃的厚度然后是鋁隔條然后還是玻璃的厚度，輸入完以后，點擊設置進入。等命令位置和當前位置數值分歧即可，留意設置時傳送帶上不要有玻璃。
First turn on the air pump switch, power supply switch, console switch, press the manual button on the console, then find the origin setting on the display screen, click the auxiliary origin setting, then click the origin setting on the head, pay attention to the origin setting to prevent the head and auxiliary sucker collision. After setting it, return to find the glass thickness setting, first the glass thickness, then the aluminium partition, then the glass thickness. After input, click Settings to enter. Just wait for the command position and the current position to diverge. Be careful not to have glass on the conveyor belt when setting.
然后是混交了，按桶膠按鈕，按工作選擇按鈕，然后按拍膠啟動，在按伐開，此時膠頭以出膠，等看不見白膠，以混平均以后按伐關，在按鏈接消費線，自動，自動運轉，此時能夠自動打膠。
Then mixing, press the first bucket of glue button, press the work selection button, then press the pat glue to start, in the press cut, at this time glue head to glue out, etc. can not see white glue, after mixing average, press cut off, in the link consumption line, automatic, automatic operation, at this time can automatically glue.
開端打膠要看每條邊每個角打膠能否平均，下面說下如何調整打膠機，在屏幕上點擊返回找到密封配方，點擊進入，會顯現當前密封壓力，假如每條邊都缺膠，那么可增加壓力，壓力大膠量大，壓力小膠量就小。

Start gluing depends on the average gluing at each corner of each side. The following is how to adjust the gluing machine. Click back on the screen to find the sealing formula. Click in, it will show the current sealing pressure. If there is a lack of glue on each side, it can increase the pressure. Large amount of pressure glue, small amount of pressure glue.
下面說下針對某條邊，或某個交，膠量不夠的調試辦法。在點擊密封配方進入后會顯現有向上密封，上部密封，向下密封，和下部密封，開端打膠的那條邊就是向上密封，然后次第從上。
The following is about the debugging method of insufficient glue for a certain edge or a certain intersection. After clicking on the sealant formula, there will be upward seals, upper seals, downward seals, and downward seals. The first side of the sealant is upward seals, and then from the top.
假如先打膠的這條邊，打膠不平均，那么點擊向上密封，進入后顯現。掃描器開后發開的時間，就是在膠嘴貼到玻璃開端挪動膠嘴出膠的時間，時間長出膠晚，時間短出膠早，掃描器開后開端挪動的時間，就是膠嘴挪動的速度，時間長挪動慢，出膠多，時間短挪動快出膠少。
If the edge of the first gluing is uneven, then click on the upward seal and appear after entering. The opening time of the scanner is the time when the glue nozzle is moved from the glue nozzle to the glass opening. It takes longer to produce glue late and shorter to get out glue early. The starting time of the scanner after opening is the speed of the glue nozzle moving. It takes longer to move slowly, more glue coming out, and less glue coming out quickly.
掃描膠量細微調整，就是只要某條邊膠少，或多，時調整掃描膠量細微調整，數值大膠量就大，數值小膠量就小。然后說下到末端伐關的間隔，數值大，膠嘴到末端膠量少，數值小膠量大。拐角時伐開的時間，就是控制拐角的膠量，數值大膠量大，數值小膠量小。假如拐角膠多就調小數值，拐角膠少，數值加大。
Fine adjustment of scanning glue quantity means that as long as there is little or more side glue in a certain strip, fine adjustment of scanning glue quantity will result in large value glue quantity and small value glue quantity. Then, the interval from the end to the end of the cut-off is large, the glue amount from the nozzle to the end is small, and the value is small and the glue amount is large. The cutting time at the corner is to control the glue quantity at the corner. The value is large, the value is small and the glue quantity is large. If the corner glue is more, the value will be reduced, while the corner glue is less and the value will be increased.
本文由全自動封膠機廠家進行編寫，想要了解更多的產品及更詳細的精彩內容，請關注我們的官方網站：http://linshi.jncsjx.com惠顧是對我們很大的支持。
This article is written by the manufacturer of automatic sealing machine. For more products and more details, please pay attention to our official website: http://m.yalais.com patronage is our great support.